Welbilt Convotherm mini black easyTouch 10.10 Installation Manual Download Page 26

Page: 26 / 148

Safety hazard: mechanical unit components

When installing the unit, keep the following hazards in mind and take the actions required in order to

eliminate and/or minimize these hazards:

Risk / hazard

Where and in which situa‐

tions will the risk/hazard ex‐

ist?

What to do

Safety device

Cut hazard posed by

sharp edges

Whenever handling sheet

metal parts

■

Exercise caution when

performing these activi‐

ties

■

Wear the required per‐

sonal protective equip‐

ment as indicated in the

relevant safety instruc‐

tions

None

Safety hazard: cleaning agents

When installing the unit, keep the following hazards in mind and take the actions required in order to

eliminate and/or minimize these hazards:

Risk / hazard

Where and in which situa‐

tions will the risk/hazard ex‐

ist?

What to do

Safety device

Skin, eye, and respira‐

tory tract irritation haz‐

ard as a result of con‐

tact with cleaning

agents and their vapors

When installing the cleaning

system

■

Wear the required per‐

sonal protective equip‐

ment

■

Observe the instructions

and warnings on the

cleaning agent labels and

in the relevant safety da‐

ta sheets

None

Whenever using aggressive

cleaning agents

Only use the cleaning

agents specified in the

'Cleaning and maintenance'

section of the operating

manual (under 'Cleaning

agents').

None

3 For Your Safety

Installation Manual

Summary of Contents for Convotherm mini black easyTouch 10.10





















































































































































Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands

Welbilt Convotherm mini black easyTouch 10.10, Installation Manual

Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands