Welbilt Convotherm mini black easyTouch 10.10 Installation Manual Download Page 53

Page: 53 / 148

6.1.3 Performing the Electrical Installation

Prerequisites

Check whether the following prerequisite is met:

■

The unit's connection point has been de-energized and locked and tagged out.

Checking the rating data and electrical connections

Follow the steps below to check the connection to the electrical system and the electrical connections:

Step

Procedure

Figure

Remove the unit's rear panel.

The circuit diagram and the spare parts list will be loca‐

ted inside the wiring compartment.

Check to make sure that the electrical rating data on the

nameplate matches the specifications in the circuit dia‐

gram and the characteristics of the building's electrical

system. Do not connect the combi oven unless all spec‐

ifications match.

Check all screw and crimp terminal connections on the

unit. The connections may have become loose during

transportation.

Performing the Electrical Installation

Follow the steps below to electrically connect your unit:

Step

Procedure

Figure

Connect the unit to an electrical ground system at the

intended connection point (1).

Check to make sure that the power cord is properly

connected to terminal block -X10 (2).

Make sure that the cable fitting (3) has a secure fit. This

fitting serves as a strain relief.

If necessary, reset the safety thermostat.

Put the unit's rear panel back in place and check that it

is mounted properly.

Connect the appropriate power plug to the power cord

(4).

Carry out the relevant country-specific electrical tests.

6 Installation

Installation Manual

Summary of Contents for Convotherm mini black easyTouch 10.10





















































































































































Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands

Welbilt Convotherm mini black easyTouch 10.10, Installation Manual

Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands