Welbilt Convotherm mini black easyTouch 10.10 Installation Manual Download Page 51

Page: 51 / 148

6 Installation

Purpose of this section

This section goes over how to connect your combi oven.

6.1 Electrical installation

Purpose of this section

This section goes over how to electrically install the unit.

6.1.1

Working Safely When Installing the Electrical Installation

For Your Safety

Before starting your work, read and understand the hazards described in Hazards and Safety Meas‐

ures During Installation on page 25.

Personnel qualifications required for electrically installing the unit

Work on electrical equipment should be performed exclusively by electricians from an authorized serv‐

ice company who have the training and certifications required by all applicable country-specific and lo‐

cal regulations.

Personal protective equipment

Wear the personal protective equipment specified for your work in the 'Personal Protective Equipment'

on page 37 section of 'For Your Safety'.

Electrical installation standards and regulations

In order to prevent hazards related to improperly installed electrical connections, make sure to ob‐

serve the following standards and regulations:

■

The connection to the power supply must be installed in accordance with the National Electrical

Code, ANSI/NFPA 70 (current edition); the Canadian Electrical Code, CSA C22.2; all other appli‐

cable national and state laws and regulations; and the local requirements set forth by the relevant

local utility companies, trade associations, and authorities.

Live parts

Risk of electric shock posed by live parts and loose cables
Electric shock may occur when coming into contact with live parts after opening the cover.

Make sure that all electrical work is performed exclusively by a qualified electrician from an

authorized customer service office.

Follow the steps below before removing the safety covers:

■

De-energize all connections.

■

Lock out and tag out all switches.

■

If the device was already energized, wait 15 minutes so that the DC bus capacitors can dis‐

charge fully.

■

Make sure that the unit is de-energized.

Before putting the unit into operation, make sure that all electrical connections are undamaged and

firmly connected.

Before putting the unit into operation, make sure that it is bonded to an electrical ground system

together with all metallic accessories.

6 Installation

Installation Manual

Summary of Contents for Convotherm mini black easyTouch 10.10





















































































































































Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands

Welbilt Convotherm mini black easyTouch 10.10, Installation Manual

Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands