Welbilt Convotherm mini black easyTouch 10.10 Installation Manual Download Page 68

Page: 68 / 148

Unsuitable supporting surfaces

Crush hazard posed by the unit falling down or toppling over
Body parts may be crushed if the unit falls down or topples over.

Make sure never to place the unit on an unsuitable supporting surface.

Contact with cleaning agents

Risk of chemical burns and skin, eye, and respiratory tract irritation
The ConvoClean new cleaning agent and the ConvoCare rinse aid will cause skin, eye, and

respiratory tract irritation upon direct contact. The ConvoClean forte cleaning agent will result in

chemical burns to the skin, eyes, and respiratory tract upon direct contact.

Do not inhale the cleaning agents' and rinse aid's vapors or mist.

Do not let the cleaning agents or rinse aid come into contact with your eyes, skin, or mucous

membranes.

Observe all the instructions and warnings on the cleaning agent labels and in the corresponding

safety data sheets when handling cleaning agents.

Wear the required personal protective equipment.

8 Removing from Service and Disposal

Installation Manual

Summary of Contents for Convotherm mini black easyTouch 10.10





















































































































































Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands

Welbilt Convotherm mini black easyTouch 10.10, Installation Manual

Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands