weinor Terrazza Originale Instructions For Assembly Download Page 59

Page: 59 / 104

Terrazza Originale

Instructions for assembly

Version 5

12.06.2017

We reserve the right to make technical changes

Item number

111361-0000

Page 59/104

5.1.2 Fitting the kinked side roof support



Before fitting the kinked side roof support, check to ensure that the gutter cap has not been

fitted to the gutter yet. The gutter cap should only be fitted after the kinked side roof support
has been fitted.



The kinked side roof support with attached clamping slider affixes to the wall bracket and

guttering.



Before laying the roof covering, make sure that the kinked side roof support is adequately

supported underneath the Knick.



This can also be done using the 135° post or 135° corner profile, both of which are

available through weinor as optional extras.



Adjust the profiles on-site and screw onto the kinked side roof support and the foundations.

Figure: Fitting the 135° post underneath the side roof support

Post, 135 degrees

Do not fit the gutter cap before the kinked side roof support has
been fitted

Summary of Contents for Terrazza Originale









































































































Search results

Summary of Contents for Terrazza Originale

Reviews:

Related manuals for Terrazza Originale

Brands by name

Popular brands

weinor Terrazza Originale, Instructions For Assembly

Search results

Summary of Contents for Terrazza Originale

Reviews:

Related manuals for Terrazza Originale

Brands by name

Popular brands