weinor Terrazza Originale Instructions For Assembly Download Page 54

Page: 54 / 104

Terrazza Originale

Instructions for assembly

Version 5

12.06.2017

We reserve the right to make technical changes

Item number

111361-0000

Page 54/104

Item Designation

Item
(untreated)

Item (painted)

Remarks

Guttering cover plate

100429

102177

Guttering cover plate for side drain

100435

102180

Cover plate for DT150 to wall

100432

102232

Cover cap for guttering angle bracket

107850

108051

Left-hand guttering cover cap, complete -

120593/ 120594

Right-hand guttering cover cap,
complete

120593/ 120594

Cap for roof support 150

109435

109872

Cover cap for post plate

108017

108127

Side roof support cover strip

116214

116240

Top profile 15x20

114926

115080

Cover profile 16 mm

101061

102223

Left wall-mounting post plate cover cap 108017

108127

Right wall-mounting post plate cover
cap

108017

108127

Aluminium base for post

None

102234

Post-to-guttering connection

100387

102175

Attachment profile for post, 180°

109030

109031

Angle bracket for post

101082

None

Gutter angle bracket

107851

108052

Guttering

101046

102215

Universal guttering coupling

109807

None

Roof support 150

101038

102207

Downspout seal

101057

None

Slide-in profile for post, 1500 mm

101172

None

Universal complete gable roof corner
joint

108482

None

53x1.5 downspout

111963

111964

53x1.5 downspout coupling

112007

112008

Gutter-to-wall anchorage

109666

109667

Small base plate for post

116837

116838

Glass support

107895

108220

Roof support glazing bead

101040

102209

Protective leaf grille

113388

None

Complete DT150 mounting plate

None

101187

Post

101048

102217

Large, reinforced post plate

101171

102248

Post plate for wall

108128

108320

Transom

101047

102121

Solar cover profile for transom

100892

102202

Pipe bend 87°

111870

111871

Clamp D53

101123

102233

Screw socket, complete

None

112061

Side wall bracket

108113

101159

Summary of Contents for Terrazza Originale









































































































Search results

Summary of Contents for Terrazza Originale

Reviews:

Related manuals for Terrazza Originale

Brands by name

Popular brands

weinor Terrazza Originale, Instructions For Assembly

Search results

Summary of Contents for Terrazza Originale

Reviews:

Related manuals for Terrazza Originale

Brands by name

Popular brands