weinor Terrazza Originale Instructions For Assembly Download Page 98

Page: 98 / 104

Terrazza Originale

Instructions for assembly

Version 5

12.06.2017

We reserve the right to make technical changes

Item number

111361-0000

Page 98/104

igure: Distance between roof support and the joint



When fitting a roof support next to a gutter joint, the distance between the centre of the roof

support to the point where the outer edge of the Terrazza meets the kink in the guttering must
be at least 100 mm.



If the angled guttering is pitched at

> 45° or more, the front of the roof supports will need to

be cut at an angle where they meet the guttering so that they do not abut against the guttering.
The roof support cover cap can no longer be fitted to the roof supports in this case.



The roof supports are covered using made-to-order plates. The cover plates must be glued

onto the roof supports.

Figure: Fitting the roof support cover plate

Glue the cover plate to the roof support

Summary of Contents for Terrazza Originale









































































































Search results

Summary of Contents for Terrazza Originale

Reviews:

Related manuals for Terrazza Originale

Brands by name

Popular brands

weinor Terrazza Originale, Instructions For Assembly

Search results

Summary of Contents for Terrazza Originale

Reviews:

Related manuals for Terrazza Originale

Brands by name

Popular brands