background image

12

Please Do Not Return This Product To The Store. 

Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your 

local yellow pages/business listings or go to the 

Find a Dealer

 section online at 

www.wayne-dalton.com

Tools Needed:

Tools Needed:

u-bar continued...

U-BAR PLACEMENT fOR TOP SECTION

U-BAR PLACEMENT fOR CENTER hINGES

U-bar

Attaching 

center 

stile

hinge

U-BAR PLACEMENT fOR END hINGES

(2) 1/4”- 14 x 7/8” 

Self drilling screws

Top bracket 

assembly

U-bar

Top 

section

U-bar

U-bar

hinge

U-bar

9

Pencil

Power Drill

5/16” Drill Bit

7/16” Wrench

Step plate

Step Plate

Locate the center most stile of the bottom section of 

the door.

On the inside of the door, center the step plate/lift 

handle on the center most stile no higher than 8” 

from the bottom of the door. Using the step plate/lift 

handle holes as a guide, drill a 5/16” dia. hole along 

each side of the stile through the face of the door. Be 

extremely careful to keep drill straight.

Mount step plates / lift handles back to back, 

straddling stile. Secure with (2) 1/4” x 2-3/4” 

carriage bolts and 1/4”-20 flange hex nuts.

INSIDE STEP PLATE INSTALLATION

OUTSIDE STEP PLATE INSTALLATION

(2) 1/4”-20 

flange hex nuts

(2) 1/4 x 2-3/4” carriage bolts

Step plate

Step plate assembly

Step plate assembly

Bottom section

Bottom section

Bottom section

8” Max mounting 

height

8” Max 

mounting 

height

Bottom section

(2) 1/4”- 14 x 7/8” Self 

drilling screws

(2) 1/4”- 14 x 7/8” 

Self drilling screws

Summary of Contents for 8124





























Reviews: