Volvo Penta 120S Workshop Manual Download Page 33

Page: 33 / 88

Repair - MS2 reverse gear and upper gear housing, sailboat drive

Upper bearing housing,
assembly

46.

Press the upper roller bearing into the bearing

housing. Use tool no.

884731

and shaft

9991801

NOTE

! The narrow ring on the bearing, at the arrow,

should face the bearing housing. Make sure that the
bearing does not go in crookedly.

47.

Install the circlip, using circlip pliers. Turn the

chamfered side down, towards the gear housing.

Make sure that the circlip is securely seated in the
groove.

48.

Put shims on the gear wheels for the upper bear-

ing housing and gear housing. Start off with 0.50 mm
for each gear wheel. This is a value which is based on
experience.

49.

Press the gear wheel into the gear housing. Use

tool no.

884728

, shaft

9991801

and

884739

as a sup-

port for the inner race.

9991801

884728

9991801

884731

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands