Volvo Penta 120S Workshop Manual Download Page 57

Page: 57 / 88

Repair of MS2V reverse gear, angle gear

18.

Install the inner roller bearing on the pinion, use

the two sleeves

884732

and

884836

19.

Place the pinion in the housing (turn the housing

so that the recessed holes for the socket cap screws
are on top). Press the other roller bearing on, using
tool no.

884732.

NOTE

! Do not press the bearing until it bottoms.

Some clearance must be left. When the nut is tight-
ened, the bearing housing is pressed together and the
clearance disappears.

20.

Apply thread locking fluid, Volvo Penta part no.

1161053-2 on the threads of the nut and install it with
the chamfered side upwards.

Start off with low torque and check the preload with a
spring balance

9985494

and a piece of string wrapped

round the bearing housing.

Pre-load:

10,0-17,5 N (2.25-3.93 lbf).

Pinion,
assembly

17.

Install the bearing races in the pinion housing with

tool

884834

and shaft

884859.

884859

884834

884732

884836

884732

9985494

2.25-3.93 lbf

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands