Volvo Penta 120S Workshop Manual Download Page 68

Page: 68 / 88

Repair - lower gear housing, sailboat drive

Propeller shaft, assembly of
bearings and drive

24.

Press the gear wheel down to the step on the pro-

peller shaft with tool no.

884753

. Make sure that it

seats securely.

25.

Install the front roller bearing with tool no.

884754

Propeller shaft, shimming

26.

For when only new bearings have been installed.

Use the previously installed shims in the first in-
stance. In other cases, the shim thickness can be
calculated as in items 27–29.

27.

Put the outer bearing race on the front ball bear-

ing. Press it hard against the bearing and measure
distance (

) with a caliper gauge, between the rear

plane of the gear wheel and the outer front plane of
the bearing race.

In this case, the distance is 100.20 mm.

28.

Dimension (

) is stamped on the starboard side of

the gear housing division to permit the shim thickness
under the front bearing race to be calculated, which is
17 in this case. The dimension of the division plane
can vary between 0 and 30.

884753

884754

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands