Volvo Penta 120S Workshop Manual Download Page 80

Page: 80 / 88

Repair - lower gear housing, sailboat drive

Oil and install a new O-ring (1) in the cutout in the
adapter plate.

74.

Fit the gear housings together. Apply MoS2 based

grease, Volvo Penta part no. 1161029-2 to the socket
cap screws. Install the screws, 10 pcs. The two long
screws should be located by the rear edge.

Put washers under the screw heads and distribute the
screws with holes in the screw heads so that there are
two on each side.

Tightening torque:

30 Nm (22.13 lbf ft)

73.

Install the adapter plate on the upper gear hous-

ing. Apply MoS2 based grease, Volvo Penta part no.
1161029-2 to the three socket cap screws. Put wash-
ers on the socket cap screws and use a torque
wrench to tighten them. Torque the screws alternately.

Tightening torque:

30 Nm (22.13 lbf ft)

Install the slipping clutch (

72.

Oil and install a new O-ring on the adapter section

neck.

Reverse installed drive (180°)

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands