Volvo Penta 120S Workshop Manual Download Page 37

Page: 37 / 88

Repair - MS2 reverse gear and upper gear housing, sailboat drive

Reverse gear MS2
Output gear housing,
assembly

62.

Install one of the outer bearing races in the bear-

ing housing. Use tool no.

884731

and shaft

9991801

NOTE

! Make sure that the bearing race does not go in

crookedly.

63.

Turn the bearing housing over and press in the

other bearing race. Use tool no.

884731

and shaft

9991801

64.

Install the cooling water pipe and install the two

larger O-rings (1). Press the small O-ring (2) onto the
screw.

65.

Apply sealant, Volvo Penta part. no. 840879-1 on

the mating face against the bearing housing.

Install the cooling water union. Check that the O-ring
is correctly aligned. Tighten the screw.

884731

9991801

884726

884731

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands