Volvo Penta 120S Workshop Manual Download Page 79

Page: 79 / 88

Repair - lower gear housing, sailboat drive

68.

Measure the thickness of gasket (

) with mi-

crometer

9999701

69.

Measure flange (

) on the adapter plate with mi-

crometer

9985472

Example:

When (

) is measured, we obtain a distance of

5.70 mm in this case.

Gasket (

) thickness is measured as 0.30 mm.

Flange height (

) is measured as 3.85 mm.

A + B – C = shim thickness

5.70 + 0.30 – 3.85 = 2.15

Shim thickness = 2.15 mm

70.

Install the calculated thickness of shims and gas-

ket on the division plane of the lower gear housing.

NOTE!

The text on the gasket must face upwards.

The hole pattern in the gasket only fits one way round.

71.

Put the rubber sleeve on the upper gear housing.

Install the cooling water tap. Apply sealant, Volvo
Penta part no. 1141570-0 on the threads.

9999701

9985472

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands