Volvo Penta 120S Workshop Manual Download Page 69

Page: 69 / 88

Repair - lower gear housing, sailboat drive

29.

The illustration shows the

dimension (

– 5

) en-

graved on the gear wheel. The other engraved figure
(

) shows the pinion which the gear wheel belongs to-

gether with. The pinion should have the same figure
engraved on it.

Example:

T = Stamped dimension on the division plane (17)

K = Engraved dimension on the gear wheel (–5)

X = Dimension measured with caliper gauge (100,20)

101 = Constant

Shim thickness = 101 + (T + K) – X

100

Shim thickness = 101 + (0,17 + – 0,05) – 100,20

Shim thickness = 101 + 0,12 – 100,20

Shim thickness = 0,92 mm

30.

Put shims of the correct thickness in the lower

gear housing. Add a further 0.05 – 0.10 mm. In this
case, we put a total of 1.00 mm shims in the housing.

Shims are available in the following standard thick-
nesses: 0.10 mm, 0.15 mm, 0.35 mm, 0.50 mm.

884754

31.

Install the outer bearing race in the gear housing

with mandrel

884756

. Use the rear bearing housing as

a guide.

32.

Press the rear roller bearing down onto the propel-

ler shaft. Use mandrel

884754

884756

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands