Volvo Penta 120S Workshop Manual Download Page 26

Page: 26 / 88

Repair - MS2 reverse gear and upper gear housing, sailboat drive

21.

Remove the cover. A lock washer, a large spring

washer, three small spring washers and possibly one
or two spacers will come away with the cover. In addi-
tion, the ball bearing and gear wheel are fixed to the
cover.

NOTE

! Remove the needle roller bearing. The bearing

might remain on the shaft.

18. Reverse gear MS2.

Turn the reverse gear upside down and remove the
bottom cover. 4 screws.

Scrap the O-ring.

19. Reverse gear MS2.

Remove the slipping clutch. Remove the sleeve bear-
ing from the vertical shaft. In some cases, the bearing
might remain in the slipping clutch.

NOTE

! If there is any fault in the slipping clutch, it

must be replaced as a unit. The clutch is only avail-
able as a complete spare part.

Change the roller bearing as necessary. Please refer
to items 73-83.

20.

Turn the reverse gear/upper bearing housing over

and put it in a press. Put tool no.

884725

over the ver-

tical shaft, so that it rests on the large washer. Press
the washer down, to release the retention ring halves.
Remove the halves.

884725

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands