Volvo Penta 120S Workshop Manual Download Page 71

Page: 71 / 88

Repair - lower gear housing, sailboat drive

Rear bearing housing,
assembly

36.

Install a new seal ring in the bearing housing, us-

ing tool no.

884752

and shaft

9991801

. Apply sealant,

Volvo Penta part no. 1161099-5, to the mating face
between the seal and the bearing housing.

NOTE!

Align the open side of the seal ring backwards

(aft).

37.

Install the other seal ring by using the same tool.

NOTE!

Align the open side of the seal ring forwards

(towards the bow). When the seal rings have been in-
stalled, the spring in the rings should face away from
each other.

38.

Apply some grease to the seal rings, Volvo Penta

part no. 828250-1.

39.

Put shims of the correct thickness in the bearing

housing. In this case, they are 0.45 mm.

40.

Assemble the outer bearing race with tool no.

884756

Oil and install new O-rings, 2 pcs.

41.

Install the propeller shaft in the gear housing.

NOTE!

Turn the shaft carefully, to avoid damaging the

sealing lips on the seal rings.

Tightening torque:

30 Nm (22.13 lbf ft).

Check the preload. Please refer to item 42.

During final assembly:

Apply sealant, Volvo Penta part no. 1161231-4, to the
mating face between the bearing housing and the
drive.

Apply thread locking fluid, Volvo Penta part no.
1161231-4, to the screws and install the bearing hous-
ing on the drive.

9991801

884752

884756

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands