Volvo Penta 120S Workshop Manual Download Page 66

Page: 66 / 88

Repair - lower gear housing, sailboat drive

Vertical shaft,
disassembly

14.

Remove the roller bearings with a knife extractor

as counterhold. Use a hydraulic press together with a
suitable mandrel.

15.

Remove the ferrule (

). Use a knife puller as a

counterhold.

NOTE

! The ferrule must always be changed when the

shaft has been removed or when the pinion has been
changed.

16.

The ground needle roller bearing race on the verti-

cal shaft should not be changed. If the roller bearing is
damaged, the entire shaft must be changed.

Then clean all components. Change worn or damaged
components.

Vertical shaft,
assembly

NOTE

! Oil all components before or during assembly.

17.

Put a

new

ferrule (

) on the vertical shaft.

18.

Install a new roller bearing with mandrel

884755

NOTE

! Press until the bearing

touches

the ferrule.

19.

Install the other roller bearing inverted, i.e. with the

smaller end upwards. Use mandrel

884755

NOTE

! Press so far that the bearings

touch

each oth-

er.

884755

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands