Volvo Penta 120S Workshop Manual Download Page 81

Page: 81 / 88

Repair - lower gear housing, sailboat drive

75.

Secure four of the screws, the ones with holes in

their heads, with locking wire, two screws on each
side as in the illustration.

Other components,
installation

76.

Install a new zinc ring.

Tightening torque:

12 Nm (8.85 lbf ft)

77.

Change the gasket on the oil drain plug.

IMPORTANT!

The gasket must be allowed soak

in oil for about 15 minutes before assembly.
Leakage would otherwise occur.

Pressure test the drive, please refer to the

Pressure

Testing

section.

Fill up with engine oil.

Please refer to

Technical Data

for oil volume, grade

and viscosity.

Check the oil level with the dipstick and install the oil
filler cap.

IMPORTANT!

When the drive is installed on the

engine the screws must be dipped in oil (includ-
ing the heads) and torqued.

Tightening torque:

20 Nm (14.75 lbf ft), alternately,
diagonally. Also do an extra
check of tightening.

Summary of Contents for 120S

























































































Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands

Volvo Penta 120S, Workshop Manual

Search results

Summary of Contents for 120S

Reviews:

Related manuals for 120S

Brands by name

Popular brands