VESPA GTS Super 125 i.e. (2009) Service Manual Download

Page: 21 / 234

Crankcase - crankshaft - connecting rod

- Measure the diameter of bushings «

» in the

three directions shown in the figure.

- Measure the diameter of the crankshaft bearings

».

- Check that the diametral clearance «

A-B

» is be-

tween the pre-set interval.

Characteristic

Diameter clearance

0.023 ÷ 0.041 mm

If value «

A-B

» is above the limit, check that value «

» is within the admissible values of the categories.

RANKSHAFT

Specification

Desc./Quantity

Category 1

28.998 to 29.004

Category 2

29.004 to 29.010

If the crankshaft is within the set limits, replace the crankshaft half-bearings mounting the crankcase

so as to suit the specified couplings. The crankcase halves can be mounted with four types of crankshaft

half-bearings identified by letters- B (blue), C (yellow), E (green).

CRANKCASE

Specification

Desc./Quantity

Category 1

32.959 ÷ 35.965

Category 2

32.953 to 32.959

CRANKCASE - CRANKSHAFT COUPLING / CRANKSHAFT HALF-BEARINGS

Specification

Desc./Quantity

Crankshaft category 1 - Crankcase category 1

E+E

Crankshaft category 2 - Crankcase category 1

C+C

Crankshaft category 1 - Crankcase category 2

C+C

Crankshaft category 2 - Crankcase category 2

B+B

Vespa GTS Super 125 i.e. (2009)

Characteristics

CHAR - 21

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands