VESPA GTS Super 125 i.e. (2009) Service Manual Download

Page: 172 / 234

Overhaul

Proceed as follows:

1) Remove the brake lever by loosening the retaining screw; open the cover (2) and take out the dia-

phragm (3);

2) remove the cap (4) and take out the internal parts in order;

3) Check that:

- The pump body shows no signs of internal damage or corrosion;

- The plunger shows no sign of damage or abnormal wear;

- The plunger return spring is in good condition.

CAUTION

ALL THE SEALS AND GASKETS MUST BE REPLACED EVERY TIME THE PUMP IS SERVICED.

1. Reservoir cap screw

2. Reservoir cap.

3. Diaphragm.

4. Bellows.

5. Sealing ring

6. Piston.

7. Gasket.

8. Spring.

9. Tank

Braking system

Vespa GTS Super 125 i.e. (2009)

BRAK SYS - 172

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands