VESPA GTS Super 125 i.e. (2009) Service Manual Download Page 81

Page: 81 / 234

FUSES

Specification

Desc./Quantity

Fuse 1

Current rating

: 30 A

Protected circuits:

Vehicle main fuse

Fuse 2

Current rating

: 7.5A

Protected circuits:

Running lights and instrument panel

illumination power

Fuse 3

Current rating

: 7.5A

Protected circuits:

Live services circuit

Fuse 4

Current rating

: 7.5A

Protected circuits:

Live injection ECU

Fuse 5

Current rating

: 7.5A

Protected circuits:

Battery power for accessories and

instrument panel

Fuse 6

Current rating

: 15A

Protected circuits:

Battery power for headlight and sad-

dle release system.

Fuse 7

Current rating

: 15A

Protected circuits:

Injection load power supply.

Dashboard

= Digital clock

= Odometer

= Speedometer

= Injection telltale light

= Engine oil pressure warning light

= Turn indicators

= High-beam warning light

= Headlight warning light

= Fuel gauge

= Low fuel warning light

= Coolant temperature gauge

= Immobilizer LED

Sealed battery

If the vehicle is provided with a sealed battery, the only maintenance required is checking its charge

and recharging, when necessary.

These operations should be carried out before delivering the vehicle, and on a six-month basis while

the vehicle is stored in open circuit.

Besides, upon pre-delivery it is therefore necessary to check the battery charge and recharge it, if

required, before storing the vehicle and, afterwards, every six months.

INSTRUCTIONS FOR THE RENEWAL RECHARGE AFTER OPEN-CIRCUIT STORAGE

1) Voltage check up

Before installing the battery on the vehicle, check the open circuit voltage with a standard tester.

- If voltage exceeds 12.60 V, the battery can be installed without any renewal recharge.

Vespa GTS Super 125 i.e. (2009)

Electrical system

ELE SYS - 81

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands