VESPA GTS Super 125 i.e. (2009) Service Manual Download

Page: 120 / 234

With injector disconnected and the injector load

remote control disconnected, check the continuity

of the Black-Green cable between the injector con-

nector and remote control base.

Inspecting the injector hydraulics

To carry out the injector check, remove the intake

manifold by removing the three clamping screws

at the head and the clip connecting the control unit

to the manifold.

Install the appropriate tool for checking fuel pres-

sure and position the manifold over a container

graduated by at least 100 cm³. Connect the injec-

tor with the cable making up part of the supply for

the injection tester. Connect the clamps of the ca-

ble to an auxiliary battery. Activate the fuel pump

with the active diagnosis. Check that, within fifteen

seconds, approximately 40 cm³ of fuel is dis-

pensed with an adjustment pressure of approxi-

mately 2.5 BAR.

Specific tooling

020480Y

Petrol pressure check set

Injection

Vespa GTS Super 125 i.e. (2009)

INJEC - 120

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands