VESPA GTS Super 125 i.e. (2009) Service Manual Download Page 24

Page: 24 / 234

- Insert the valves into the cylinder head.

- Alternatively check the intake and exhaust

valves.

- The test is carried out by filling the manifold with

petrol and checking that the head does not ooze

through the valves when these are just pressed

with the fingers.

Measure the camshaft bearing seats and rocking

lever support pins with a bore meter

HEAD BEARINGS

Specification

Desc./Quantity

Bearing "A"

37 +0.025

Bearing "B"

20 +0.021

Bearing "C"

12 +0.018

- Measure the unloaded spring length.

Characteristic

Standard length

40.5 mm

Allowable limit after use:

39.7 mm

- Clean the valve seats of any carbon residues.

- Using the Prussian blue, check the width of the

impression on the valve seat "

Characteristic

Admissible limit:

1.6 mm

- If the width of the impression on the valve seat exceeds the specified limits, replace the cylinder head.

Characteristics

Vespa GTS Super 125 i.e. (2009)

CHAR - 24

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands