VESPA GTS Super 125 i.e. (2009) Service Manual Download Page 124

Page: 124 / 234

5. Fuse No. 2; 7.5A

6. Injection load remote control

7. Fuel pump

8. HV coil

9. Fuel injector

10.Electric fan remote control

11.Coolant electric pump

The ignition system is integrated with the injection and it is a high-efficiency inductive type ignition.

The control unit manages two important parameters:

- Ignition advance

This is optimised according to the engine rpm, to the engine load, temperature and ambient pressure

With idle engine, it is optimised to obtain the stabilisation of the speed at 1450 ± 50 R/1'.

- Magnetisation time

The coil magnetisation time is controlled by the control unit. The ignition power is increased during the

engine start-up phase.

The injection system recognises the 4-stroke cycle and therefore, ignition is only controlled during

compression.

Specific tooling

020331Y

Digital multimeter

Check that the injection load 15A fuse No. 3 works

properly.

Check that the 7.5A fuse No. 2 for live control unit

power works properly.

Check there is voltage between pins 22 and 26 of

the interface wiring for around two seconds when

switching to «

».

Injection

Vespa GTS Super 125 i.e. (2009)

INJEC - 124

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands