VESPA GTS Super 125 i.e. (2009) Service Manual Download

Page: 143 / 234

- Refit the fifth wheel fitting and the dust guard on

the steering tube until they stop, using the specific

tool.

Specific tooling

006029Y

Punch for fitting fifth wheel seat on

steering tube

- Use the specific tool to fit the fifth wheel fitting on

the headstock as indicated in the figure

Specific tooling

001330Y

Tool for fitting steering seats

- Remove the steering tube

- Remove the attachment bracket

- Use the specific tool with the part 1 and operate

the handgrip until removing temporarily the pin and

the Nadella opposite the tool thrusting direction.

- To extract the second Nadella, use the tool with

the part 2, instead of part 1, on opposite side to the

one indicated in the figure.

Specific tooling

020021Y

Front suspension service tool

- Fit both dust guard rings

«C»

on the swinging hub

as shown in the detail drawing

«A»

- Connect the swinging hub to the steering tube

with the guiding pin, part 5.

- Use the specific tool fitted with part 3 on the stem

and part 4 on the tool base.

- Lubricate the pin with recommended grease and

insert it temporarily on the swinging hub, move the

tool handgrip until part 3 is fully inserted on the

steering tube.

Vespa GTS Super 125 i.e. (2009)

Suspensions

SUSP - 143

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands