VESPA GTS Super 125 i.e. (2009) Service Manual Download

Page: 187 / 234

Front mudguard

- First remove the steering tube and uncouple the

front brake pipes from the calliper in order to re-

move the front mudguard

- Remove the three mudguard-steering tube

clamps indicated in the figure

Radiator fan

- In order to carry out any operation on the radiator

unit, flow out the coolant in the coolant delivery

pipe in the pump, indicated in the photograph.

- Remove the shield back plate;

- Remove the coolant feed and return hoses from

the right radiator;

- Unscrew the 4 screws fixing the radiator to the

body;

- Detach the radiator

- Detach the pipe from the plastic duct by removing

the plastic clip shown in the photograph. Then re-

move the duct.

Vespa GTS Super 125 i.e. (2009)

Chassis

CHAS - 187

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands