VESPA GTS Super 125 i.e. (2009) Service Manual Download

Page: 144 / 234

- Once the pin has been fitted, insert the two

spacers part 17 slightly hitting with a mallet (see

next figure).

CAUTION

USE NEW ROLLER CASINGS, PIN, SEALING RINGS AND
DUST GUARDS FOR REFITTING.

Specific tooling

020021Y

Front suspension service tool

Recommended products

AGIP GREASE PV2

Grease for steering bear-

ings, pin seats and swinging arm

Soap-based lithium and zinc oxide grease con-

taining NLGI 2; ISO-L-XBCIB2 of the swinging arm

To fit sealing rings, roller casings and wedging

washers proceed as follows

- Lubricate the sealing rings with mineral oil and

half-fill the roller casings with recommended

grease.

- Insert the sealing ring on the pin and the roller

bushing with wedging washers at the same time.

- Remove the specific tool and then the part 5

(guide) partially ejected in the previous assembly

stage; part 4 must be always fitted.

- Replace part 3 with part 16 on the stem.

- Push, from the handgrip, the wedging washer -

roller casing - sealing ring unit, placing part 16 until

it stops on the swinging hub

- Repeat the operation described above using the

tool fitted with part 16 and part 22* instead of part

4 on the stem, on the side opposite the one shown

in the figure to refit the second wedging washer -

roller casing - sealing ring unit.

Suspensions

Vespa GTS Super 125 i.e. (2009)

SUSP - 144

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands