VESPA GTS Super 125 i.e. (2009) Service Manual Download

Page: 157 / 234

Shock absorber lower fitting

40 ÷ 45

Upper shock absorber fixing screws

20 ÷ 25 Nm

Exhaust bracket

Removal

Remove the full muffler unit.

- Remove the two fixing screws of the bracket to

the engine crankcase

- Remove the split pin, the cover and the fixing nut

of the rear wheel axle and its spacer

- Remove the shock absorber lower clamp

Refitting

- The refitting procedure is in the reverse order of the removal operation being careful to respect the

torques indicated and the spacer assembly layout as shown in the photo.

Locking torques (N*m)

Bracket fixing screws to the engine crankcase:

20 ÷ 25

Shock absorber lower fitting

40 ÷ 45

Wheel axle clamping

104 ÷ 126

Centre-stand

REMOVAL

- Use a jack to support the vehicle properly.

- Remove the two return springs from the centre

stand.

- Undo the nut shown in the figure.

- Remove the pin from the right side.

- Remove the centre stand.

FITTING

- On refitting tighten the nut to the specified torque.

Locking torques (N*m)

Centre stand bolt

32 ÷ 40

Vespa GTS Super 125 i.e. (2009)

Suspensions

SUSP - 157

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands