VESPA GTS Super 125 i.e. (2009) Service Manual Download

Page: 153 / 234

- Separate the swinging arm on the engine side

from the vehicle side arm.

- Remove the plastic bushings and the internal

spacer shown in the picture.

- Using a suitable pin remove the roller casings as

shown in the pictures

- Using an appropriate tool plant new roller cas-

ings, being careful to position the bearings with the

O-rings facing outwards

Specific tooling

020244Y

15-mm diameter punch

020115Y

Ø 18 punch

Characteristic

Length of the swinging arm tube on the engine
side:

L 175.3 + 0.3 0

Length of the internal swinging arm spacer on
the engine side:

L 183 + 0.3 0

Engine side swinging arm plastic bushing
shim:

3.5 ± 0.05 mm

Chassis side swinging arm plastic bushing
shim:

3.5 ± 0.05 mm

Length of the internal swinging arm spacer on
the frame side:

290 ± 0.1 mm

Vespa GTS Super 125 i.e. (2009)

Suspensions

SUSP - 153

Summary of Contents for GTS Super 125 i.e. (2009)











































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands

VESPA GTS Super 125 i.e. (2009), Service Manual

Search results

Summary of Contents for GTS Super 125 i.e. (2009)

Reviews:

Related manuals for GTS Super 125 i.e. (2009)

Brands by name

Popular brands