Valet Digital Instruction Manual Download Page 33

Page: 33 / 64

User Close

The alarm is armed.

System Reboot

The alarm has been turned on with the keyswitch.

System Battery Failed

The backup battery has failed or requires to be

charged.

Periodic Test Failed

The Valet Monitoring Station failed to

communicate with the alarm panel for more than

seven days.

Event Log Full

This means that your system has received too

many alarms before it could send them to the

Valet monitoring station. The most probable cause

is that the Main Control Unit has been unable to

communicate with the monitoring station for some

time.

System Shutdown

This means that a serious problem has occurred

and your system has had to shut down. Please

contact your installer immediately or Valet

Monitoring on 1300 302 293

Billing Failed

Your alarm panel has failed when it called the

1900 number for your monthly billing. Check that

the phone line is plugged in, there is a dial tone on

the line and that your line is enabled to call 1900

and 1300 numbers. Your control panel will not

work until your billing is successful.

High Level Radio

Interference

System is experiencing a high level of

interference, which may prevent normal alarm

activation.

External Siren Reboot

The external siren has been turned off and back

on again

External Siren Power

Loss

There has been no power supplied to the External

Siren for 15minutes. The External siren is running

off the backup battery

External Siren Battery

Fail

The External Siren’s back up battery is outside

normal operating conditions and may be unable to

run correctly in the event of Main power loss.

External Siren

Supervision fail

The External Siren has failed to communicate with

the main control unit for 24hours

External Siren Tamper

The Tamper switch on the external siren has

changed state.

If your alarm system is unable to contact the VALET MONITORING CENTRE

it will retry to send the message five more times at 25 second intervals. If

unable to send the message after these attempts, the message will be lost, so

it is important to ensure that your phone line is always connected to your alarm

panel.

Summary of Contents for Digital

































































Search results

Summary of Contents for Digital

Reviews:

Related manuals for Digital

Brands by name

Popular brands

Valet Digital, Instruction Manual

Search results

Summary of Contents for Digital

Reviews:

Related manuals for Digital

Brands by name

Popular brands