Utax CD 1435 User Manual Download Page 98

Page: 98 / 250

FAX Operation (Advanced)

4-30

NOTE:

To enable FTP Encrypted TX setting, be sure

that

SSL

Secure Protocol

. For details, refer to

the machine's

Operation Guide

File Separation

If transmission is by e-mail or to a folder (SMB) or folder (FTP), set whether page division is performed.

Follow steps 1 to 4 of

Using Requirements for All

Receptions on page 4-20

Follow steps 1 to 3 and 14 of

Using Rule for

Specific RX on page 4-22

Select the requirement and press [Detail].

Press [Change] of

File Separation

Press [Off] or [Each Page].

To have one file created for each page, select
[Each Page].

Press [OK].

Setting a Number of Copies

You can set whether the machine should print received originals when forwarding them. You can specify the
number of copies.

Follow steps 1 to 3 of

Using Requirements for All

Receptions on page 4-20

Follow steps 1 to 3 of

Using Rule for Specific RX on

page 4-22

Select the requirement and press [Detail].

Press [Change] of

Print

Press [On] or [Off].

If you selected [On], press [+]/[-] or numeric keys to
set the number of copies.

Press [OK].

Summary of Contents for CD 1435



























































































































































































































































Search results

Summary of Contents for CD 1435

Reviews:

Utax CD 1435, User Manual, Page: 98 / 250

Search results

Summary of Contents for CD 1435

Reviews: