Unify OpenScape CP700 User Manual Download Page 105

Page: 105 / 243

105

Making calls

Receiving a call

The call number or name of caller will be shown on the display.

Answering a call via the handset

The phone rings.

Lift the handset

Answering a call via the loudspeaker (speakerphone
mode)

The phone rings.

Press key. LED is lit

Press the Softkey

shown.

Answering a call via the headset

Prerequisite:

A headset is connected.

The phone rings. The

key flashes.

Press key

Rejecting calls

You can reject a call you do not wish to accept. The call is then sent to another
definable phone (consult relevant Administrator).

Press the Softkey

shown.

To better understand the steps described here, it is recommended that you
read the introductory chapter "”Getting to know the OpenScape Desk Pho-
ne CP700/CP700X”

1. Set volume

Answer

Reject call

Summary of Contents for OpenScape CP700




















































































































































































































































Search results

Summary of Contents for OpenScape CP700

Reviews:

Related manuals for OpenScape CP700

Brands by name

Popular brands

Unify OpenScape CP700, User Manual

Search results

Summary of Contents for OpenScape CP700

Reviews:

Related manuals for OpenScape CP700

Brands by name

Popular brands