Unify OpenScape CP700 User Manual Download Page 124

Page: 124 / 243

124

During the call

Switching to speakerphone mode

Prerequisite:

You are conducting a call via the handset.

Press and hold the key, hang up the handset, and then release the key and con-
tinue the call.

US mode

If the country setting is set to US (ask relevant Administrator), you do not need
to press the loudspeaker key when you hang up the phone.

Press key.

]

Replace the handset. Proceed with your call.

Switching to handset mode

Prerequisite:

You are conducting a call via speakerphone mode.

and

[

Lift the handset. Proceed with your call. The hands-free microphone is switched
off.

Open listening in the room during a call

You can allow other people in the room to listen in on a call. Let the other party
know that you have turned on the loudspeaker.

Prerequisite:

You are conducting a call via the handset.

Activating

Press key. LED lights up. The hands-free microphone remains off.

Deactivating

Press key. LED goes out.

Summary of Contents for OpenScape CP700




















































































































































































































































Search results

Summary of Contents for OpenScape CP700

Reviews:

Related manuals for OpenScape CP700

Brands by name

Popular brands

Unify OpenScape CP700, User Manual

Search results

Summary of Contents for OpenScape CP700

Reviews:

Related manuals for OpenScape CP700

Brands by name

Popular brands