UNI-T UTG9000T Series User Manual Download

Page: 102 / 162

UTG9000T Series Function Abitrary Waveform Generator

102

modulation wave. The carrier wave width changed by the modulation wave amplitude. The
modulation modes for each channel are independent, it can set the same or different modulation
modes to each channel.

Select PWM modulation

Tap

CH1

→

Modulate

→

PWM to turn on PWM modulation, the instrument output the moduluated

waveform according to the current setting of the modulation wave and the carrier wave.

Select the carrier waveform

PWM carrier waveform can only be pulse wave.

After select PWM modulation, tap Base to present

the carrier waveform on the right side.

Carrier wave frequency settings

Refer to The carrier wave frequency settings of AM modulation.

Summary of Contents for UTG9000T Series



































































































































































Search results

Summary of Contents for UTG9000T Series

Reviews:

Related manuals for UTG9000T Series

Brands by name

Popular brands

UNI-T UTG9000T Series, User Manual

Search results

Summary of Contents for UTG9000T Series

Reviews:

Related manuals for UTG9000T Series

Brands by name

Popular brands