WES WES-250 Manual Download

Page: 1 / 20

World Environmental Solutions Pty Ltd.

Manual for a WES 250L and WES 500L

Ⅰ. Summary --------------------------------------------------------------------------------------1

Ⅱ. Technical Specifications -------------------------------------------------------------------1

Ⅲ. Working Principle -------------------------------------------------------------------------2

Ⅳ. Machine Acceptance, Installation and Adjustment -----------------------------------2

Ⅴ. Operation----------------------------------------------------------------------------------------3

Ⅵ. Precautions

------------------------------------------------------------------------------------------------9

Ⅶ. Maintenance

-----------------------------------------------------------------------------------------------10

Ⅷ. Troubleshooting

-------------------------------------------------------------------------------------------------11

ANNEX I -------------------------------------------------------------------------------13

ANNEX II ------------------------------------------------------------------------------18

ANNEX

Ⅲ

-----------------------------------------------------------------------------19

Notice

：

This machine does not install RO film in it by default. Please install RO film inside the

machine before starting. (Please follow page 14 CLEAN AND REPLACE RO FILTERS to install)

The pictures in this instruction manual are only for reference purposes only.
NOTE: There may be technical changes or changes in structural design without prior notification

Summary of Contents for WES-250





















Search results

Summary of Contents for WES-250

Reviews:

Related manuals for WES-250

Brands by name

Popular brands

WES WES-250, Manual

Search results

Summary of Contents for WES-250

Reviews:

Related manuals for WES-250

Brands by name

Popular brands