manualshive.com logo in svg

UNI-T UTG9000T Series, User Manual, Page: 69 / 162

Share
Download
UNI-T UTG9000T Series User Manual Download Page 69

UTG9000T Series Function Abitrary Waveform Generator                                          

 

69 

 

The shape of the 4FSK modulation waveform viewed through an oscilloscope is shown in the 
figure below, 

 

 

 

3.1.8 PSK (Phase Shift Keying) 

In PSK modulation mode, the function/arbitrary waveform generator can move between in two 
preset phases (carrier phase and hopping phase) According to the logical level of the modulating 
signal to output the carrier frequency or hopping frequency. The modulation modes for each 
channel are independent, it can set the same or different modulation modes to each channel.

 

 

Select PSK modulation   

Tap 

CH1

→

Modulate

→

PSK to turn on PSK modulation, the instrument output the moduluated waveform 

according to the current phase setting (default 0

°

and can’t adjustable) of the modulation wave and the 

carrier wave.

 

Summary of Contents for UTG9000T Series



































































































































































Reviews:

No comments