manualshive.com logo in svg

UNI-T UTG9000T Series, User Manual, Page: 121 / 162

Share
Download
UNI-T UTG9000T Series User Manual Download Page 121

UTG9000T Series Function Abitrary Waveform Generator                                          

 

121 

4) Turn on the output channel 

Tap channel Out botton to ON or push CH1 key on the front panel to quick set the output 
channel,and it can aslo turn on at the Utility interface,tap Utility

→

Channel

→

Output or 

double-click the channel tab bar at the bottom of the screen to step through ON/OFF. CH1 
key and CH1 tab bar backlight light on indicating that the channel 1 output is turned on. 

 

The shape of the burst waveform viewed through an oscilloscope is shown in the figure 
below, 

 

 

 

 

3.4 Output Abitrary Waveform 

UTG9000T hs store more than 200 standard waveform types in non-volatile memory. See Table 
4-4 (Built-in Arbitrary Waveform). The instrument can creat and edit arbitrary waveform by USB 
interface to read arbitrary data file on the front panel.   
 

Summary of Contents for UTG9000T Series



































































































































































Reviews:

No comments