manualshive.com logo in svg

UNI-T UTG9000T Series, User Manual, Page: 52 / 162

Share
Download
UNI-T UTG9000T Series User Manual Download Page 52

                                          UTG9000T Series Function Abitrary Waveform Generator 

52                                                                           

 

The shape of the PM modulation waveform viewed through an oscilloscope is shown in the figure 
below, 

 

 

 

 

3.1.4 ASK (Amplitude Shift Keying) 

ASK is a digital amplitude modulation, it expresses digital signals “0”and “1”by changing the 
amplitude of carrier signal. And according to the logical of modulation signal to output the carrier 
signals with different amplitude. The modulation modes for each channel are independent, it can 
set the same or different modulation modes to each channel. 

 

Select ASK modulation

 

Tap 

CH1

→

Modulate

→

ASK to turn on ASK modulation, the instrument output the moduluated 

waveform according to the current setting of the modulation wave frequency and the carrier wave. 

Summary of Contents for UTG9000T Series



































































































































































Reviews:

No comments