UNI-T UTG9000T Series Page 42 User Manual Download | Manualshive

Page: 42 / 162

background image

UTG9000T Series Function Abitrary Waveform Generator

42

Select the carrier waveform

The carrier wave of AM: sine, square, ramp, pulse and arbitrary wave (except DC), the default
option is sine wave. After select FM modulation, tap Base to present the carrier waveform on the
right side.

Carrier wave frequency settings

Refer to The carrier wave frequency settings of AM modulation.

Select the source of modulation

UTG9000T function/arbitrary waveform generator can select internal or external modulation source.
When turn on FM modulation, the default modulation source is internal. Rotate multifunction knob or tap

ModSrc tab to step through internal or external modulation source in FM modulation setting interface.

«
...
40
41
42
43
44
...
»

Summary of Contents for UTG9000T Series



































































































































































Reviews:

No comments

Related manuals for UTG9000T Series

Brand: Olin Pages: 14

Brand: iHome Pages: 2

QUIKCELL PartyBeat Power

Brand: Alpha Comm Enterprises Pages: 14

Brand: Generac Power Systems Pages: 16

Brand: R&S Pages: 79

Brand: ekston Pages: 10

Brand: Curtis Pages: 22

Brand: Curtis Pages: 24

Brand: Motorola Pages: 55

Brand: Motorola Pages: 20

Brand: Motorola Pages: 4

Brand: Motorola Pages: 15

Brand: Motorola Pages: 21

Brand: Motorola Pages: 4

Brand: Motorola Pages: 96

Brand: Motorola Pages: 103

Brand: Motorola Pages: 132

Brand: Motorola Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands