manualshive.com logo in svg

UNI-T UTG9000T Series, User Manual

Share
Download
UNI-T UTG9000T Series User Manual Download Page 36

                                          UTG9000T Series Function Abitrary Waveform Generator 

36                                                                           

Select AM Modulation 

Tap  CH1

→

Modulate

→

AM  to turn on the AM modualtion, the instrument output the moduluated 

waveform according to the current setting of the modulation wave and the carrier wave. 

 

Select the carrier waveform 

The carrier wave of AM: sine, square, ramp, pulse and arbitrary wave (except DC), the default option is 
sine wave. After select AM modulation, tap Base to present the carrier waveform on the right side. 

 

Carrier frequency settings 

The frequency range of the carrier wave can set differently, all the default fundamental frequency 
is 1kHz, see Table 4-1 and Table 4-2 for the frequency settings of the different carrier waveform. 

Table 4-1 The carrier wave frequency of CH1 and CH2   

 

Carrier waveform 

Frequency 

UTG9604T 

UTG9404T 

UTG9204T 

MIN 

MAX 

MIN 

MAX 

MIN 

MAX 

Sine wave   

1uHz 

600MHz  1uHz 

400MHz 

1uHz 

200MHz 

Summary of Contents for UTG9000T Series



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands