manualshive.com logo in svg

UNI-T UTG9000T Series, User Manual, Page: 96 / 162

Share
Download
UNI-T UTG9000T Series User Manual Download Page 96

                                          UTG9000T Series Function Abitrary Waveform Generator 

96                                                                           

After the parameter setting of the carrier wave, tap Type to return to DSB-AM modulation 
interface to set the modulation wave nd frequency. 

 

  

Tap ModWave tab to pop-out visual numeric keyboard to select square wave.   
Tap ModFreq tab to pop-out visual numeric keyboard to enter 1kHz.

 

 

4

）

Turn on the output channel 

Tap channel Out to ON or push CH1 on the front panel to quick set the output channel,and it 
can aslo turn on at the Utility interface,tap Utility

→

Channel

→

Output or double-click the 

channel tab at the bottom of the screen to step through ON/OFF. CH1 and CH1 tab backlight 
light on indicating that the channel 1 output is turned on. 

 

The shape of the AM modulation waveform viewed through an oscilloscope is shown in the 
figure below, 

Summary of Contents for UTG9000T Series



































































































































































Reviews:

No comments