manualshive.com logo in svg

Trox Technik EM-IP, Configuration Manual, Page: 50 / 80

Share
Download
Trox Technik EM-IP Configuration Manual Download Page 50

ManOp_Disable

BMS access: WR RD

Equipment function:

EASYLAB
–

FH, RR with RMF, TAM with RMF

TROX UNIVERSAL
–

RE/RS with RMF, PR*/PD* with RMF

Function

Enabling/disabling manual control

Upon enabling manual control the corresponding

symbol appears on the control panel.

For further information on manual control please

refer to the EASYLAB design manual.

FH: Operating mode default setting for a fume cup-

board controller, only with individual operating mode

default setting (stand-alone operation)

RMF: operating mode default setting for the entire

room

Functional values

0: Manual control has been enabled on the control

panel.
Operating mode defaults set on DI override BACnet

or Modbus defaults.

1: Manual control has been disabled on the control

panel.
Operating mode default settings from BACnet or

Modbus have the highest priority.

Data point

BACnet: Binary Value Object – Instance BV-4

Modbus: Bit list - bit 0 or register 1

PressSetSel

BMS access: WR RD

Equipment function:

EASYLAB
–

RR with RMF, TAM with RMF

TROX UNIVERSAL
–

not used

Function

Input for switching between two pressure set points

when differential pressure control of the system is

activated (setpoint values stored in the room man-

agement function).

Functional values

0: Use differential pressure setpoint 1

1: Use differential pressure setpoint 2

Data point

BACnet: Binary Value Object – Instance BV-5

Modbus: Bit list - bit 1 or register 13

DO*_Set (BACnet) / DO_Set (Modbus)

BMS access: WR RD

Equipment function:

EASYLAB
–

FH, RR, RR with RMF, EC, SC, TAM, TAM with

RMF

TROX UNIVERSAL
–

RE/RS, RE/RS with RMF, PR*/PD*, PR*/PD*

with RMF

Function

Control input signal for unused switch outputs DO1

– DO6 of the controller or adapter module

Data point

BACnet: Binary Value Object – Instance BV-19

(DO1_Set) – Instance BV-24 (DO6_Set)
–

0 = output inactive

–

1 = output active

Modbus: Register 61 – bit 0 (DO1_Set) – bit 5

(DO6_Set)
–

Bit not set = output inactive

–

Bit set = output active

Interface information

Data points – detailed description  > Input variables

 

Expansion module EM-IP

50

Summary of Contents for EM-IP

















































































Reviews:

No comments