Trango Systems M2400S User Manual Download Page 47

Page: 47 / 50

Trango Broadband Wireless — User Manual M2400S Rev. A

Page

Command Radio

Description

Access

default = -60

tftpd

AP/SU

display current TFTPD status (status is either on or off) This
command will also list any contents of the TFTP buffer.

ro/rw

tftpd <on | off>

AP/SU

enable or disable TFTPD service. TFTPD must be on in order to
upload new firmware or new SUDB file.

updateflash <systemsetting | ss>

AP/SU

Save current settings. This command can be issued in several ways:
save ss, updateflash systemsetting, save systemsetting, and
updateflash ss

updateflash <mainimage | fpgaimage>
<current chscksum> <new checksum>

AP/SU

Retrieve uploaded firmware from TFTP buffer, verify checksum,
and write to flash memory at main or FPGA image section.

updateflash sudb

Save SUDB into flash memory

ver AP/SU

Display

firmware and date codes

1.  Version number and date code
2.  Firmware and FPGA version code
3.  Firmware and FPGA image checksum

ro/rw

Summary of Contents for M2400S



















































Search results

Summary of Contents for M2400S

Reviews:

Related manuals for M2400S

Brands by name

Popular brands

Trango Systems M2400S, User Manual

Search results

Summary of Contents for M2400S

Reviews:

Related manuals for M2400S

Brands by name

Popular brands