Trango Systems M2400S User Manual Download Page 30 | Manualshive

Page: 30 / 50

background image

Basic

Configuration via CLI

Trango Broadband Wireless — User Manual M2400S Rev A

Page

26

!

Important!

When changing settings, it is usually necessary to type the

save ss

command in order to update

the radio’s flash memory. If you do not type the

save ss

command, the setting will be lost the next time the

radio is rebooted or power cycled.

SU SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS

SU Parameter

Description

Related CLI Command

Device ID

MAC Address of the SU

N/A

Base ID

Specifies the cell or cluster to
which the SU belongs.

set baseid <baseid>

Example:

#>Set baseid aa12

Target AP

If unique AP ID selected, the
SU can only associate with
the specified AP. If ALL is
selected, the SU can
associate with any AP with a
matching BASE ID.

targetap <apid>

Examples:

#>targetap 33

#>targetap all

Opmode

Current Opmode of radio.

opmode on y

- set Opmode to “ON.” (note: “y”

is necessary if default Opmode is “OFF.”)

opmode off

– set Opmode to “OFF.”

Default Opmode

Determines the Opmode
(“ON” or “OFF”) of the radio
after reboot/power cycle.
When this parameter is set to
“ON,” the radio will progress
into Opmode “ON”
automatically after
reboot/power cycle.

set defaultopmode <on

or

off>

Example:

#>set defaultopmode on

IP
Subnet
Gateway

IP, Subnet, and Gateway
address of radio.

ipconfig [<new ip> <new subnet mask> <new
gateway>]

Example:

#>ipconfig 10.1.1.3 255.0.0.0 10.1.1.1

TFTPD

TFTPD status (on or off).
TFTPD should be turned on
to import a file into the radio
(such as new firmware).
Default is off. TFTPD will
revert to off after
reboot/power cycle.

tftpd [<on|off>]

Example:

#>tftpd on

RF TX Power

Current transmit power of the
SU not including antenna
gain. This is controlled by
the AP.

Informational Parameter – can not be manually
changed by user.

Active Channel

Shows the channel used in
the current association, and
"Associated" or
"Disconnected" depending
on the association status.

If Autoscan AP (SW 1) is on, the active channel
(and antenna selection) will be set once the SU
scans and begins the association process with an
AP.
If Autoscan AP is off, the active channel is set by
the user, using the

freq

command.

freq [<ch#> <v|h>]

Example:

«
...
28
29
30
31
32
...
»

Summary of Contents for M2400S



















































Reviews:

No comments

Related manuals for M2400S

Brand: D-Link Pages: 61

Brand: Icom Pages: 2

PremierWave 2050

Brand: Lantronix Pages: 2

Brand: Pakedge Pages: 7

Brand: Pakedge Pages: 4

Brand: ZyXEL Communications Pages: 15

Brand: FS Pages: 12

Brand: Tenda Pages: 80

Brand: H3C Pages: 18

TG-RouterE-PM-01-100

Brand: Telegesis Pages: 9

Brand: HPE Pages: 4

Brand: UPT Solar Pages: 8

Brand: Icom Pages: 88

Brand: PI Manufacturing Pages: 64

Brand: Air Live Pages: 18

Brand: Ebyte Pages: 17

Brand: Ebyte Pages: 23

Brand: Ebyte Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands