Trango Systems M2400S User Manual Download | Manualshive

Page: 39 / 50

background image

Deployment

Trango Broadband Wireless — User Manual M2400S Rev A

Page

35

4 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0  [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0  5
00 ms  5120 kbps
5 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0  [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0  5
00 ms  5120 kbps
6 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0  [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0  5
00 ms  5120 kbps
7 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0  [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0  5
00 ms  5120 kbps
8 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0  [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0  5
00 ms  5120 kbps
9 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0  [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0  5
00 ms  5120 kbps

[AP Total nTx]   1000 pkts
[AP Total nRx]   1000 pkts
[AP Total nRxErr] 0 pkts

[SU Total nTx]   1000 pkts
[SU Total nRx]   1000 pkts
[SU Total nRxErr] 0 pkts

[AP to SU Error Rate] 0.00 %
[SU to AP Error Rate] 0.00 %

[Avg of Throughput] 5120 kbps

#> Success.

su testrflink <suid>

This command also checks the integrity of the wireless link from the standpoint of over-the-air packet loss. In this test,
the AP will send 20 large (1512 byte) packets to the SU, and the SU will in turn send the same 20 packets back to the AP.
The expected result of an error free link is 20..20..20, indicating (in the following sequence) 20 packets sent from AP, 20
packets received back at AP, and 20 packets received at the SU. Any results other than 20..20..20 indicates a performance
problem, most likely due to interference or inadequate signal to noise ratio. For thorough results it is recommended you
run the command repeatedly for at least 1 minute or more to determine if packets are passing without error consistently
over time. This command will give results without the help from ARQ. Note: This test does not provide as much detail
as the

linktest

command.

The “r” is used in this command to repeat the RF link test repeatedly until the user terminates the test by hitting SPACE
ENTER.

Example:
#> su testrflink 1 r

Press [space] then [enter] to stop
[len] 1512
[suid] 1
[   0] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
[   1] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
[   2] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
[   3] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
[   4] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
[   5] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
Success.
#>

As another example, a result of 20..10..18 would indicate 20 packets sent from the AP, 18 packets received at the SU, and
10 packets received back to the AP. These types of results may be caused by Fresnel zone infringements, interference, or
multi-path.

«
...
37
38
39
40
41
...
»

Summary of Contents for M2400S



















































Reviews:

No comments

Related manuals for M2400S

Brand: Ublox Pages: 44

Brand: Ebyte Pages: 10

iPAQ Connection Point CP-1

Brand: Compaq Pages: 50

MTX-Router-Titan

Brand: Titan Pages: 200

BLUESOCKET 3040

Brand: ADTRAN Pages: 6

BLUESOCKET 2135

Brand: ADTRAN Pages: 8

RTA2600 HighPower

Brand: Amped Wireless Pages: 2

Brand: Amped Wireless Pages: 2

TITAN-AP APA1900

Brand: Amped Wireless Pages: 78

Brand: Wunda Pages: 2

Brand: HPE Pages: 4

Brand: UPT Solar Pages: 8

Brand: Spectrum 24 Pages: 142

Brand: Westermo Pages: 28

Brand: Icom Pages: 2

QuecOpen AG521R-NA

Brand: Quectel Pages: 93

Conduit AP MTCAP-LAP3-915-041

Brand: Multitech Pages: 27

Brand: Sierra Wireless Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands