Trango Systems M2400S User Manual Download Page 4 | Manualshive

Page: 4 / 50

background image

Preface

Trango Broadband Wireless — M2400S User Manual Rev A

page iv

Preface

This manual covers basic configuration and installation of the M2400S Wireless Broadband System and applies to
the following radio part numbers:

M2400S-AP

2.4 GHz Access Point

M2400S-SU

2.4

GHz

Subscriber

Unit

FCC Information

This device complies with Part 15 of FCC Rules and Regulations. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and radiates radio-frequency energy; if not installed and
used in accordance with these instructions, the unit may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in any particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to correct the interference by one or more of the following measures:

1)  Reorient the antenna.
2)  Increase the separation between the affected equipment and the unit.
3)  Connect the affected equipment to a power outlet on a different circuit from the one the receiver is connected

to.

4) Consult the dealer and/or experienced radio/TV technician for help.

FCC ID: NCYM2400S
Canada:

IMPORTANT NOTE:

Intentional or unintentional changes or modifications must not be made unless under the

express consent of the party responsible for compliance. Any such modifications could void the user’s authority to
operate the equipment and will void the manufacturer’s warranty. To comply with FCC RF exposure requirements,
the following antenna installation and device operating configurations must be satisfied. The antenna for this unit
must be fixed and mounted on an outdoor permanent structure with a minimum separation distance of two meters
from any persons. Furthermore, it must not be co-located or operated in conjunction with any other antenna or
transmitter.

Warranty Information

Radios from Trango Broadband Wireless are warranted for one year from date of purchase. Please see

www.trangobroadband.com

for a complete description of warranty coverage and limitations.

Firmware Notifications

To receive email notifications regarding firmware upgrades and product announcements, register at

http://www.trangobroadband.com/mailinglist/mailingListAdd.aspx

«
...
2
3
4
5
6
...
»

Summary of Contents for M2400S



















































Reviews:

No comments

Related manuals for M2400S

Brand: Quantum Pages: 8

Brand: Quantum Pages: 21

Brand: Quantum Networks Pages: 27

Brand: Xylem Pages: 20

UHF Wireless Series

Brand: LD Pages: 5

Brand: ZyXEL Communications Pages: 11

AI Buddy Plai WiFi

Brand: Gyrfalcon Technology Pages: 14

EVlinking Wi-Fi

Brand: Evco Pages: 18

Brand: Linksys Pages: 124

Brand: Zte Pages: 51

Brand: HPE Pages: 4

Brand: HPE Pages: 4

Brand: q-Tech Pages: 12

Brand: Ebyte Pages: 13

Road Runner Mobile

Brand: Sierra Wireless Pages: 9

Brand: Sierra Wireless Pages: 11

Brand: Tycon Power Systems Pages: 4

Brand: Canyon Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands