Trango Systems M2400S User Manual Download | Manualshive

Page: 43 / 50

background image

Management

Trango Broadband Wireless — User Manual M2400S Rev A

Page

39

b. trango.ico – M900S AP icon
c. autoico.txt – instruction file (Selects Trango icon automatically during initial set-up.)
d. readme.pdf

3.  Copy trango_m2400sap_1p0.mib file to C:\Program Files\SNMPc Network Manager\mibfiles
4.  Copy autoico.txt file to C:\Program Files\SNMPc Network Manager\mibfiles
5.  Copy trango.ico file to C:\Program Files\SNMPc Network Manager\bitmaps
6.  The MIB needs to be compiled into the SNMPc database

By default, the Read Community is set to “

public

,” and the Write Community is set to “

private

” in the AP. The Trap

Community is “

SNMP_trap

.” The manager needs to have the same settings in order to communicate with the AP

successfully.

To send traps from the AP set the following:

•

trap destination IP (Trango MIB object trapconfig–trapconfigInfo)

•

trap community string (Trango MIB object trapconfig–aptrpTable-AptrpEntry)

•

enable each trap (Trango MIB object traponfig–aptrpTable-AptrpEntry)

«
...
41
42
43
44
45
...
»

Summary of Contents for M2400S



















































Reviews:

No comments

Related manuals for M2400S

Brand: BridgeWave Pages: 84

Dual-Band Wi-Fi Kit 600

Brand: BT Pages: 6

Brand: Ubiquiti Pages: 16

Brand: Skyrc Pages: 2

Brand: NETGEAR Pages: 2

Brand: Tenda Pages: 80

Brand: Cambium Networks Pages: 24

WAP51AB - Instant Wireless - Access Point

Brand: Linksys Pages: 2

Brand: Arista Pages: 6

Brand: Air Live Pages: 74

Brand: Air Live Pages: 72

Brand: Air Live Pages: 74

Brand: Ubiquiti Pages: 26

Passport MDE-5412

Brand: GILBARCO VEEDER-ROOT Pages: 96

Brand: NETGEAR Pages: 102

Brand: Kajeet Pages: 2

Brand: ZComax Pages: 3

Brand: 3Com Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands