Trango Systems M2400S User Manual Download | Manualshive

Page: 16 / 50

background image

Basic

Configuration via Browser Interface

Trango Broadband Wireless — User Manual M2400S Rev A

Page

12

CIR DOWN:

Committed Information Rate from AP to SU. Minimum downstream rate (measured in Kbps)
at which the AP will attempt to deliver bandwidth to that SU. Maximum setting is 5200.

MIR UP:

Maximum Information Rate from SU to AP. Maximum upstream rate (measured in Kbps) at
which the SU will attempt to deliver bandwidth to the AP. Maximum setting is 5200.

MIR DOWN:

Maximum Information Rate from AP to SU. Maximum rate (measured in Kbps) at which the
AP will attempt to deliver bandwidth to that SU. Maximum setting is 5200.

DEVICE ID:

MAC address of the SU.

Creating an SU in the SUDB

1. Connect to the AP (see Getting Started) and open the Subscriber Database page.

2. Enter the SU ID (range 1 – 126).

3. Select either PRIORITY or REGULAR.

4. If the SU will be part of an SU to SU group, enter the SU to SU group number.

5. CIR up (SU to AP Committed Information Rate) is the minimum upstream bandwidth for the SU in Kbps.

6. CIR dn (AP to SU Committed Information Rate) is the minimum downstream bandwidth for the SU in

Kbps.

7. MIR up (SU to AP Maximum Information Rate) is the maximum upstream bandwidth for the SU in Kbps.

8. MIR dn (AP to SU Maximum Information Rate) is the maximum downstream bandwidth for the SU in

Kbps.

«
...
14
15
16
17
18
...
»

Summary of Contents for M2400S



















































Reviews:

No comments

Related manuals for M2400S

Brand: BridgeWave Pages: 84

8760 - Wireless Dual Radio 11a/b/g PoE Access...

Brand: 3Com Pages: 8

Brand: Linksys Pages: 30

MAX-STREAM EA7250

Brand: Linksys Pages: 20

Brand: iBall Baton Pages: 62

Brand: Pakedge Device & Software Pages: 57

Brand: Sandberg Pages: 12

Brand: Atlantis Land Pages: 83

WebShare 144 WN+

Brand: Atlantis Pages: 19

Brand: Acoustic Research Pages: 6

Brand: SkyLink Pages: 4

Brand: VideoHome Pages: 21

Brand: Z-Com Pages: 35

Constellation series

Brand: VERITAS Pages: 8

Brand: 3Jtech Pages: 8

OfficeConnect 3CRWE454G75

Brand: 3Com Pages: 50

Brand: D-Link Pages: 24

Barricade SMC7904WBRA

Brand: SMC Networks Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands