Trango Systems M2400S User Manual Download Page 49

Page: 49 / 50

Trango Broadband Wireless — User Manual M2400S Rev. A

Page

LO stability:

+/- 2.5 ppm PLL stabilized over temperature

Ethernet I/O Specifications

Data Input/Output:

Connector:

Shielded

RJ-45

Jack

Signaling Format:

IEEE802.3i (10baseT) and IEEE802.3u (100baseT) compliant

Filtering:

PPPoE

per

RFC

2516

(SU

only)

Auto-Negotiation:

Fully supports IEEE802.3-2002 Sect. 2 Clause 28

Bridging Frame Size:

60 to 1600 bytes

Mngmt Frames:

60 to 1472 bytes. (includes PING, TELNET, TFTP, HTTP)

Protection:

Bi-directional

transient

voltage protection diodes on all data lines

compliance with:
IEC61000-4-2 (ESD)
IEC61000-4-4 (EFT)
IEC61000-4-5 (Lightning)

Power Specifications

Input Voltage:

Input voltage range at unit is 10.5 VDC to 24 VDC max

Power is supplied via unused pins of the RJ-45 Jack. Power is
injected into Ethernet cable using a junction box (J-Box) provided.

Current Cons.:

500 mA in transmit and receive modes at max power using 20 V
standard adapter (10 W) and 10 ft cable from J-Box to unit

Protection:

28 volt Transient Voltage Suppression (TVS) diode on power input
Note: Voltages above 28 volts will cause damage to unit.

Mechanical and Environmental Specifications

General
Material:

High temp polycarbonate radome and diecast metal enclosure

Size:

12.5” x 8” x 2.75” including mounting studs

Weight:

Mounting:

2 U-Brackets, all-thread rod, nuts and washers

Connectors/Indicators
RF

Output:

Integral

internal

patch antenna per Part 15C, 15.203

External RP-SMA-f connector for external antenna

FCC Compliance: The transceiver complies with the following:

FCC Part 15.247
FCC Part 15.207(a)

Environmental
Operating Temp:

-40 to 60 deg C

Storage:

-40

deg

Humidity:

100 % when sealed properly

NEMA Rating: NEMA 4
Shock:

Sustain 3 axis drop from 5 feet

Standard External Power Supply

20 Volt DC Power adapter and J-Box supplied with product.

Summary of Contents for M2400S



















































Search results

Summary of Contents for M2400S

Reviews:

Related manuals for M2400S

Brands by name

Popular brands

Trango Systems M2400S, User Manual

Search results

Summary of Contents for M2400S

Reviews:

Related manuals for M2400S

Brands by name

Popular brands